However, it’s missing on the third key point: The voltage makes sense (microphone provides the phantom power) So, in general, I think that your post makes sense on two points:Ģ. The impedance of the NTG-2 is 350Ω with phantom power but the iPhone is used to something higher than 1000Ω (the Apple earphones are 1600Ω from what I saw on the internet). This is because although the connectivity makes sense and the mic provides the phantom power, there is a mismatch on impedance. However the iPhone does not recognize the mic. I plugged everything together, quite the same as your setup except the different mic. – Rode NTG-2 (it provides its own 48v phantom power using a AA battery inside). Here is the setup I tried following your setup : The only missing adapter on my side was the Rode SC4 TRS to TRRS, so I went to buy one. I was curious too to use a shotgun mic to identify far birds using the Merlin Bird ID iOS app. I say this because both of them are longer in length, and microphones, if treated well, will last a long time, so used is great. The MKE 600 is still being produced, but personally, I would look at used options of either of the former two before opting for this one. I love both the Sennheiser ME66 and ME67. The shotgun mic is going to be way more directional and will help suppress the sounds of birds coming from other directions. My best advice is to look for a shotgun mic from a reputable brand that you can find that is available. This accessory controls the gain level before the signal reaches the phone and will help your final recordings sound better with less editing in post.Ģ. If you’re too far, the bird is hard too see, but too close and the whole bird won’t fit in the frame (when audio input is too loud, it can clip and become distorted). Think of it like zooming in or out with a camera lens to get the bird centered nicely in the frame. You’d typically boost the gain when the bird is farther and quieter, and reduce it when your subject is closer and louder. The main purpose of an accessory like this is to fine-tune the gain (essentially the loudness of the recording). I haven’t done a direct comparison of the same subjects using both setups to give a confident answer on this yet, but that is a great idea for a new blog post, thank you!Īnother commenter made an excellent recommendation for using another accessory in this setup (the iRig Pre HD Class-A XLR mic preamp). This should allow the phone to recognize everything properly.Ī quick test of this setup shows my audio being recorded in Merlin using the external mic while ignoring the built-in one. So, in short, to get things working properly plug all the dongles and cables together THEN plug them into the phone. The folks at the store were kind enough to help me plug everything in and confirm it worked before paying. Rather than wait for another online shipment, I found a camera store nearby that sells the Rode SC4 TRRS Adapter that I needed. I learned that the microphone cable outputs its signal as “TRS” and needs to be converted to “TRRS” for the iPhone hence the extra dongle I mentioned above in the course’s setup. The microphone was being powered with its battery, but the phone was still using the built-in mic when running Merlin. My microphone has an XLR output so I bought an XLR female-to-male 3.5mm cable and plugged it all in with the 3.5mm-to-Lightning adapter. Check out my current setup for birdsong recording using a dedicated recorder.Įxamining this video course closer (they didn’t go into the detail of the setup), I could see they plugged the microphone into the 3.5mm-to-Lightning adapter with another dongle in between. This setup should work with any XLR microphone. I decided to go down this rabbit hole of researching what I would need to connect my Sennheiser ME66 microphone to my iPhone. This setup allowed them to get higher-quality recordings and get Merlin’s help IDing what was vocalizing. While taking an online course on How to Record Bird Sounds, one of the setups they showed in the video utilized an external microphone connected to an iPhone running Merlin. I’ve used my existing microphone setup with a dedicated recorder since I picked up the equipment.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |